(813) 803-6535 Book a Repair
Model library · U-Line ice machine

U-Line BI95 repair

Legacy built-in crescent ice maker. Service for this model across Tampa Bay.

U-Line ice maker repair in Tampa Bay
Model
BI95
Type
Legacy built-in crescent ice maker
Years
Legacy model
Brand
U-Line

About the BI95

The BI95 follows the older numbering, with 95 for the cabinet and BI for built-in. Crescent ice comes from its harvest cycle, and a lever in the bin ends the run rather than an electronic sensor, so its behavior is simple to interpret.

Moving parts decide how a BI95 ages, so we begin with the harvest motor that turns every cycle, then the inlet valve that fills the mold and may no longer close cleanly. The bin lever is last, since a lever that sticks halts production. We state the price in writing before working.

What we check on a BI95 visit

  • Harvest motor, when cycles slow or stop
  • Inlet valve shutoff, when the mold overfills
  • Bin lever movement, when ice production halts

Key features

  • Built-in crescent ice maker under the legacy numbering
  • The 95 cabinet code plus the BI prefix
  • Crescent ice made in a harvest cycle
  • Bin-full shutoff by a mechanical lever

The model number is on the serial label: inside the cabinet near the top, on the side wall or behind the front grille. We are an independent repair company, not affiliated with U-Line Corporation.

Error codes

U-Line ice machine codes

Codes listed for U-Line ice machines. Which ones a unit can show depends on its control generation, so we confirm by the full model number.

All error codes

11Reservoir Water Too HighU-Line ice machine12Water Level Low in the ReservoirU-Line ice machineCLU-Line Echelon 2000 Ice Maker "CL": Self-Cleaning Cycle RunningU-Line ice machineCLR2060 one flashU-Line CLR2060 One Flash: Overflow Protection Circuit Open (P-60)U-Line ice machineCLR2060 two flashesU-Line CLR2060 Two Flashes: Open Thermistor or Machine Too WarmU-Line ice machineCLRCO2075 LED 2 flashingU-Line CLRCO2075 LED 2 Flashing: Open Thermistor After OverheatingU-Line ice machineCLRCO2075 LED 3 flashingU-Line CLRCO2075 LED 3 Flashing: Drain Pump Blocked or OverloadedU-Line ice machineDrain BlockedLED 3 Flash Count and P60U-Line ice machine
More models

Other U-Line ice machine models

U-Line ice maker repair in Tampa BayModular 3000 Series3018CLR18-inch Modular clear ice machineU-Line ice maker repair in Tampa BayModular 3000 Series3045CLRWide Modular clear ice machineU-Line ice maker repair in Tampa BayADA SeriesACP11515-inch ADA clear ice machineU-Line ice maker repair in Tampa BayADA SeriesACR01414-inch ADA crescent ice makerU-Line ice maker repair in Tampa BayADA SeriesACR01515-inch ADA crescent ice makerU-Line ice maker repair in Tampa BayADA SeriesACR11515-inch ADA crescent ice makerU-Line ice maker repair in Tampa BayIce MachineADA15IMOlder 15-inch ADA ice makerU-Line ice maker repair in Tampa BayADA SeriesANB11515-inch ADA nugget ice machine
FAQ

BI95 questions

How does the BI95 know the bin is full?

A mechanical lever rides on the ice in the bin and trips a switch. If the lever sticks, the machine may stop too soon or run too long, so we check its travel.

Why does my BI95 leak water into the bin?

An inlet valve that no longer shuts cleanly lets water drip into the mold between cycles. We test the valve and replace it if it seeps.

Call Book a Repair
Call (813) 803-6535 Book a Repair